Waterworks Highgate Pressure Balance Control Valve Trim with User Manual download pdf

HIGHGATE

Pressure Balance Control Valve Trim

INSTALLATION GUIDELINES

Page 1 of 3

6.5.2012

These guidelines have been prepared for the professional contractor to aid in the installation of:

HIGHGATE PRESSURE BALANCE TRIM WITH PORCELAIN LEVER HANDLE (STYLE# HGPB10)

All dimensions are based on original specification and are subject to change and variation.

Please consult your Design Associate for current specifications.

White Porcelain Lever Handle

Style No. HGPB10

SPECIFICATIONS:

Rough-in Depth Minimum: 1-7/8"

Rough-in Depth Maximum: 2-7/8"

Integrated Diverter: No

REQUIRED PLUMBING DETAILS:

Universal Pressure Balance Valve

STYLE # GUPB81R

CODE # GUSV81R

IMPORTANT:

¾ To ensure this product is installed properly, you

must read and follow these guidelines.

¾ The owner/user of this product must keep this

information for future reference.

¾ This product is intended to work with the

Waterworks Universal Pressure Balance Valve (Style

# GUPB81R). The risk of scalding exists until the

installer has properly calibrated/adjusted the

temperature setting during final trim installation.

¾ The bottom outlet of the GUSV81R is intended for

use with a tub spout with an integrated diverter

only.

¾ Do not use Pex piping from the valve to the tub

spout. This will cause too much back pressure for

the valve to function properly.

¾ Be sure your installation conforms to federal state,

and local codes. In the State of Massachusetts, all

installations must comply with the rules and

regulations set forth within 248 CMR.

¾ This product must be installed by a professional

licensed contractor.

¾ Refer to the specifications and assembly drawings

attached. Product is sold partially assembled but

shown fully disassembled for illustrative and service

purposes only.

¾ Inspect this product to ensure you have all the parts

required for proper installation.

¾ This product must be on-site prior to rough-in which

allows the installer to visualize the installation.

¾ Use only a strap wrench or protected/smooth-jaw

wrench on any finished surface.

VALVE OPERATION:

1. When the finished wall is complete, turn on the hot

and cold supplies and pull off the tile guard. Valve

will not operate unless BOTH supplies are turned on.

2. The lever handle (5) is for controlling the

temperature only, not volume. Place the handle on

the valve stem so it rests at 6 o'clock in the OFF

position and then turn the handle counter clockwise

through the cold, then warm and stopping at the hot

position. If additional rotational friction is required to

maintain the handle position, tighten the packing

nut.

3. Allow the valve to run in the warm position for a few

minutes to completely flush the system. If system is

quite dirty, remove valve spindle to ensure proper

flushing. Refer to the Installation Guidelines for the

Pressure Balance Valve which contains a complete

parts breakdown and related information.

Figure - 01

Valve Spindle

Plastic Washer

Bonnet

Finished Wall

Packing Nut

1 2 3 4 5 6 7 8 9

Summary of Contents

Page 1 - INSTALLATION GUIDELINES

HIGHGATE Pressure Balance Control Valve Trim INSTALLATION GUIDELINES Page 1 of 3 6.5.2012 These guidelines have been prepared for the professio

Page 2

HIGHGATE Pressure Balance Control Valve Trim INSTALLATION GUIDELINES Page 2 of 3 6.5.2012 These guidelines have been prepared for the professio

Page 3

HIGHGATE Pressure Balance Control Valve Trim INSTALLATION GUIDELINES Page 3 of 3 6.5.2012 These guidelines have been prepared for the professio

Page 4 -  

STYLE HGPB10Highgate Pressure Balance Control Valve Trim with White Porcelain Lever Handles STYLE HGPB30 Highgate Pressure Balance with Di

Page 5 - WATERWORKS

1WWW.WATERWORKS.COM/STUDIOWELCOME TOOver thirty years of experience distilled intosignature ﬁ ttings, surfaces, textiles, and accessories. Waterworks

Page 6 - MAIN KITS

32 WWW.WATERWORKS.COM/STUDIOPRODUCT SUPPORT: 1 (800) 927-2120 (EXT 2)*FINISH/COLOR MUST BE SPECIFIED WHEN ORDERING++SUPPLIED AS A PAIRSTYLES: HGPB10,

Page 7 - KIT COMPONENTS

54 WWW.WATERWORKS.COM/STUDIOPRODUCT SUPPORT: 1 (800) 927-2120 (EXT 2)*FINISH/COLOR MUST BE SPECIFIED WHEN ORDERING++SUPPLIED AS A PAIRSTYLES: HGPB10,

Page 8 - SERVICE PARTS INDEX

77 WWW.WATERWORKS.COM/STUDIOSTYLE PGDESCRIPTIONDOCUMENT: SPHG_REV*FINISH/COLOR MUST BE SPECIFIED WHEN ORDERING++SUPPLIED AS A PAIRSERVICE PARTS IN

Page 9 - DANBURY, CT 06810

PRODUCT SUPPORT60 BACKUS AVENUEDANBURY, CT 068101 (800) 927-2120 (EXT 2)WWW.WATERWORKS.COM/STUDIO

Comments to this Manuals

No comments

Waterworks Highgate Pressure Balance Control Valve Trim with User Manual

Browse online or download User Manual for Accessories for water Waterworks Highgate Pressure Balance Control Valve Trim with . Waterworks Highgate Pressure Balance Control Valve Trim with White Porcelain Lever Handle User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Accessories for water Waterworks Highgate Pressure Balance Control Valve Trim with